岩棉板制造商的外墙保温施工过程主要包括：基础处理，胶粘剂配置，固定装置，底部抹灰砂浆，耐碱网眼布，表面抹灰砂浆，保温系统验收和装饰层施工。我们的齐工岩棉板厂家今天要谈论的是粘贴岩棉板的过程。

 

The external wall insulation construction process of rock wool board manufacturer mainly includes: foundation treatment, adhesive configuration, fixing device, bottom plastering mortar, alkali resistant mesh cloth, surface plastering mortar, insulation system acceptance and decorative layer construction. Our Qinghai rock wool board manufacturers today to talk about the process of sticking rock wool board.

 

齐工岩棉板

 

1.粘贴时，从底部到顶部用粘结砂浆铺砌岩棉板。岩棉板的长边在水平方向上放置和粘贴。垂直接缝应逐行错开1/2线，且板长等于或大于200mm。

 

1. When sticking, place rock wool board from bottom to top with binding mortar. The long sides of the rock wool board are placed and pasted in a horizontal direction. The vertical joints shall be staggered 1/2 line by line and the length of the plate shall be equal to or greater than 200mm.

 

2.墙角两侧的岩棉板应错开重叠，并应确保墙角的垂直性。

 

2. The rock wool boards on both sides of the corner shall be staggered and overlapped, and the perpendicularity of the corner shall be ensured.

 

3.开口（如门窗）的四个角应切成整块岩棉板，不要拼接。岩棉板的接缝与开孔四个角之间的距离应大于200mm，开口四侧其他岩棉板的宽度应不小于200mm。

 

3. The four corners of openings (such as doors and Windows) should be cut into a whole rock wool board, do not join. The distance between the joint of the rock wool board and the four corners of the opening shall be greater than 200mm, and the width of the other rock wool board on the four sides of the opening shall be no less than 200mm.

 

4.均匀地按压岩棉板，使其完全粘附在基础层上。粘结砂浆的压实厚度尽量控制在3mm之内。

 

4. Press the rock wool board evenly to make it adhere to the base layer completely. The compaction thickness of bonding mortar should be controlled within 3mm as far as possible.

 

5.随时使用2m斜尺和电线支架检查平面度和垂直度，如果不符合要求，请立即进行校正。

 

5. Use 2m inclined scale and wire bracket to check the flatness and perpendicularity at any time. If it does not meet the requirements, please correct it immediately.

 

6.立即刮下板缝和板侧面之间的残留砂浆。

 

6. Immediately scrape off the residual mortar between the seams and the sides of the board.

 

7.岩棉板之间的间隙应控制在1.5mm之内，接头之间的高度差应控制在1mm之内。如果接头的宽度超过1.5毫米，则可用适当宽度的岩棉板条填满缝隙，注意不要让板条粘住。

 

7. The gap between rock wool boards should be controlled within 1.5mm, and the height difference between joints should be controlled within 1mm. If the width of the joint exceeds 1.5 mm, rock wool slats of appropriate width may be used to fill the gap, taking care not to allow the slats to stick.

 

另外，请关注生产岩棉板的厂家官方网站，以了解更多有关齐工岩棉条产品的信息。您可以直接联系在线客服或留言，我们将竭诚为您提供更好的服务！

 

免责声明：本网站上的某些文章和图片来自Internet，仅供参考。版权属于原始作者。如果您的权利受到侵犯，请与我们联系，我们将尽快处理。